Stuck On It: The Magigoo Adhesive Guide for Every UltiMaker & Tectonic-3D Filament

September 18, 2026

Stuck On It: The Magigoo Adhesive Guide for Every UltiMaker & Tectonic Filament

A warped first layer is still the #1 reason a print fails before it's even started. We just brought in the full Magigoo build plate adhesive lineup — 17 products covering everything from everyday PLA to PEKK. Here's exactly which Magigoo goes with which filament we sell, so you stop guessing.

💡 Why bed adhesion still breaks prints

Every filament chemistry releases from a build plate differently. A PEI sheet that holds PLA perfectly will let a nylon part pop loose mid-print, and the reverse is just as true — an adhesive dialed in for engineering filament can leave PLA welded to the plate. Magigoo builds a separate formula for each material family instead of one "do everything" glue, which is why picking the right bottle matters as much as picking the right filament.

🧴 The Magigoo lineup at 3D3

Magigoo Original & Magigoo Supergrip — the everyday pair, for standard filaments on standard or coated/flex plates.

The PRO line — PP, PC, PPGF, PA, Flex, HT, and Metal — single-material formulas built for engineering filaments, plus the PRO Kit bundling PA, PC, PP and Original.

The Glide system — the Glide Roller applicator plus 250ml refills (Supergrip, PA, PC, PP, HT) for print farms and multi-printer shops, plus the Glide Kit with Supergrip starter bundle.

Browse the full lineup on the Magigoo collection page.

📊 Filament compatibility chart

This maps every Magigoo product to the specific UltiMaker filaments and Tectonic-3D filaments we stock — not a generic materials list. If a filament isn't linked under a formula, we don't currently carry a match for it (see the special cases section below).

Magigoo adhesive → compatible UltiMaker & Tectonic filaments sold at 3D3 Technology
Magigoo product	Formulated for	Compatible filaments in our catalog
Magigoo Original	PLA · ABS · PETG	✅ UltiMaker PLA Filament ✅ UltiMaker Tough PLA Filament ✅ Sketch Series Filament – PLA ✅ Sketch Series Filament – Tough PLA ✅ UltiMaker ABS Filament ✅ AURA ABS EC ✅ UltiMaker PET-G Filament ✅ Kratir PETG CF ✅ KRATIR PET CF
Magigoo Supergrip	PLA · PETG · ABS/ASA · TPU	✅ UltiMaker PLA Filament ✅ UltiMaker Tough PLA Filament ✅ Sketch Series Filament – PLA ✅ Sketch Series Filament – Tough PLA ✅ UltiMaker PET-G Filament ✅ UltiMaker ABS Filament ✅ AURA ABS EC ✅ Aura ASA+ ✅ UltiMaker TPU Filament Best for coated, satin, or flexible build plates specifically — same materials as Original, different plate type.
Magigoo PRO PP & Glide PP	Polypropylene	✅ Kratir PP CF AO ✅ KRATIR PP CF
Magigoo PRO PC & Glide PC	PC · PC alloys	✅ UltiMaker Polycarbonate Filament ✅ PYRA PC/ABS FR
Magigoo PRO PA & Glide PA	PA6 · PA6/66 · PA12 & filled nylons	✅ UltiMaker Nylon Filament ✅ UltiMaker Nylon CF SLIDE ✅ KRATIR PA11 CF ✅ KRATIR PA6/66 CF ✅ Zephyr PA11 CF MC
Magigoo PRO Flex	TPU · TPC / TPE elastomers	✅ UltiMaker TPU Filament ✅ ANASA TPC 80A ✅ ANASA TPC 95A ✅ ANASA TPC L80A
Magigoo PRO HT & Glide HT	PEEK · PEKK (up to 150°C bed)	✅ VULCAN PEKK-A
Magigoo PRO PPGF	Glass-filled polypropylene	No current 3D3 filament match — see special cases below.
Magigoo PRO Metal	Metal-filled (e.g. BASF Ultrafuse 316L)	No current 3D3 filament match — see special cases below.
Magigoo PRO Kit	PA + PC + PP + Original	The four formulas above, bundled — covers nylon, polycarbonate, polypropylene, and everyday filaments in one kit.
Magigoo Glide Roller	Applicator tool	Not chemistry-specific — pairs with any Glide refill above. Compatibility follows whichever refill you load.
Magigoo Glide Supergrip	Same as Supergrip	250ml roller refill — same filament list as Magigoo Supergrip above.
Magigoo Glide Kit with Supergrip	Same as Supergrip	Roller + 250ml Supergrip + cleaning cloth — same filament list as Magigoo Supergrip above.

⚠️ Special cases & what's not covered yet

CPE and CPE+ (UltiMaker CPE, UltiMaker CPE+, AURA CPE) don't get a dedicated PRO formula. Magigoo's own guidance is to use Magigoo Original with a slightly higher build-plate temperature, since CPE and PET-family materials can warp otherwise.

UltiMaker PPS-CF is an ultra-high-temperature engineering filament that Magigoo doesn't explicitly list in its compatibility documentation (its PRO HT sheet names PEEK and PEKK specifically). PRO HT is the closest formulated match for a high-temp engineering resin, but run a test tile before committing a full job.

Support & soluble materials — UltiMaker Breakaway, UltiMaker PVA, PROTEOS Breakaway, and PROTEOS PVA print alongside your primary material rather than needing their own bed adhesion — prep the plate for whichever structural filament you're pairing them with.

PPGF and metal-filled filaments — PRO PPGF and PRO Metal are in our lineup ready to go, but we don't currently stock a glass-filled PP or a metal-filled filament (like BASF Ultrafuse 316L) to pair them with. If that's in your queue, ask us — sourcing is easy to add.

🎯 Which Magigoo do I need?

You're printing…	Grab this
Standard PLA, ABS, or PETG on a PEI plate	Magigoo Original
Same materials, but on a flex or coated plate	Magigoo Supergrip
Nylon or nylon-CF (PA)	Magigoo PRO PA
Polycarbonate or PC-ABS	Magigoo PRO PC
Polypropylene-CF	Magigoo PRO PP
TPU or TPC flexibles	Magigoo PRO Flex
PEKK-A or another PEEK/PEKK-family resin	Magigoo PRO HT
Running a print farm or multiple printers	Magigoo Glide Kit + refills
Not sure yet / want the essentials in one box	Magigoo PRO Kit

✅ Get set up

Every one of these pairs a specific Magigoo formula to a filament we actually stock — no guessing which glue stick to grab off a generic compatibility chart. If your material isn't listed above, or you're not sure which formula fits your setup, our team will match you to the right bottle before you waste a print.

Ready to stop fighting first layers?

Shop the full Magigoo lineup, or the UltiMaker and Tectonic filaments it's built for.

Shop Magigoo Shop UltiMaker Filament Shop Tectonic Filament Email Our Team

Back to blog

Your cart is empty

Your cart

Estimated total